Check the 9 volt battery under the keypad numbers. To access, press inward, under the number pad lip while sliding downward to expose the battery. This small black button is located behind the light lens at the motor head and is nearest the floppy 6 inch antenna wire that protrudes from the power head.
When pressed, a radio signal indicator will start blinking red for 30 seconds. With most Genie units, remove the light lens globe to expose the Learn Button on the motor head.
The learn button is sometimes located on the back of the unit, or with Excelerator openers, it is under the light lens near the hinge of the lens globe. Always locate the floppy antenna wire first. The Learn Button can be found not far from this antenna.
See Troubleshooting Guides for Excelerator photo. You can then print out a legible copy of the chart and programming steps from your word software. Programming Instructions for the GWKP Genie garage door opener keyless entry involves following the two sets of steps below:.
It is usually behind the light lens and close to the floppy antenna wire. If your Door Opener does not have an antenna, you have an External Receiver. Follow Steps 1 through 3 outlined below:. Works with Genie systems using Intellicode 1 and Intellicode 2 controls. Intellicode 1 refers to all systems made from to Present, with the exception of and Intellicode 2 refers to most units made in and The keypad should now be set to the new PIN.
The outside garage door keypad has a flat ribbon, which slides behind the garage door molding into the garage, and attaches to the Keyless Entry Receiver box. Slide the switch to SET. Slide the receiver switch back to RUN. Test your PIN code followed by the star button. The square smart button is located on the side or the back of the motor head, and is colored red, green, amber, orange, or purple. It is directly under the 1 wire terminal screw.
Record the dip switch sequence before performing steps. For every switch in the ON or positive position record a 1, for every switch in the OFF or negative position record a 2. Back light should turn off after step 4. If you are using the one-button remote G1T shown here: Please hold the button for approximately 10 seconds prior to pressing your HomeLink button, then press your HomeLink button down as well — holding both sets of buttons down until the indicator on the HomeLink blinks slowly and then fast.
You are now ready to program your HomeLink to an opener. In the following. As you hold both buttons down, the indicator on your HomeLink should blink slowly then fast. If neither of these applies, please continue below. Press and release the learn code button - the red LED will begin to blink. Press the desired HomeLink button one time. The red LED will stop blinking and stay on. Press the desired HomeLink button one more time.
The red LED will go out. Pressing the HomeLink button again will cause the garage door to move. Your remote is now programmed.
Press the square button once more until the long purple LED comes on and release. The purple LED should be blinking. To unlock the programming feature use a remote that already operates the unit and press it once. Purple light goes solid. Hold the new remote 4 or 5 feet away and press 3, 4 or 5 times until the door activates.
The remote is then programmed Clearing Memory for Remotes and Keypad if present Follow steps 1 and 2 above or step 1 if between and July 8, This clears the receiver memory. All previously programmed remotes will no longer work with your door. To re-program each remote follow steps 1 through 3 of the programing instructions relative to your opener above.
Programming Digital Remote Transmitters with Internal Set Switches These transmitters work by matching the settings on the internal code setting switches with the same set of switches in the receiver on the garage ceiling.
To program a button for one of your doors, follow the instructions below: First, match the settings on the Internal Code Setting Switches with the same set of switches in the receiver on the garage ceiling, as described in the previous programming instructions. Follow the same procedure for each additional door you wish to program. Installation of Genie GIC Intellicode Receiver Terminals labeled 1, 2 and 3 on the Receiver are connected to their corresponding terminals on the garage door opener Power Head labeled 1, 2 and 3.
The smart indicator light will glow steadily for 30 seconds. The LM and LM remotes have a corresponding amber or red, square, learn button.
The LM and LM have a corresponding purple, square, learn button.
0コメント